Dataset Viewer
input
stringclasses 1
value | instruction
stringlengths 202
3.29k
| output
stringlengths 193
312
| category
stringclasses 1
value | index
stringclasses 1
value | fileName
null |
|---|---|---|---|---|---|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌｧｲﾊﾞｰ前準備",
"WorkItems": [
"1. にLABEL を取付ける",
"2. 1完成品の黒ｲﾝｼｭﾛｯｸを切り､ との先端を揃えて固定する"
],
"WorkPoints": [
"OPT1K311のﾀｸﾞを取り外すﾌｧｲﾊﾞｰに傷を入れ無い事",
"ｲﾝｼｭﾛｯｸを切り取るﾌｧｲﾊﾞｰに傷を入れ無い事",
"6/7K302",
"200㎜",
"200㎜",
"200㎜",
"黄色ﾏｰｷﾝｸﾞが合っている事",
"20㎜",
"OPT1/2K311",
"3/4K351"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"4K351",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "束線前準備",
"WorkItems": [
"1. にLABEL を貼付ける",
"2. 1完成品にCONNECTOR を取付ける"
],
"WorkPoints": [
"ｸﾞﾛﾒｯﾄ取り外す",
"左右ｾﾝﾀｰ合わせ(目視)",
"3㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "束線前準備",
"WorkItems": [
"1. にLABEL を貼付ける",
"2. 1完成品にCONNECTOR を取付ける"
],
"WorkPoints": [
"ｸﾞﾛﾒｯﾄ取り外す",
"左右ｾﾝﾀｰ合わせ(目視)",
"3㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "7㎜BOX",
"ToolOther": "194cN･m",
"WorkName": "ﾘﾝｸﾞI/O負荷基板取付け",
"WorkItems": [
"1. 本体にSPACER を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"★静電対策作業",
"★静電対策作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾘﾝｸﾞI/O負荷基板取付け",
"WorkItems": [
"★2. 1完成品に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"REAR"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"★静電対策作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "静電対策工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｧｲﾊﾞｰ線投入・接続",
"WorkItems": [
"2. を接続する",
"1. をﾌﾛﾝﾄ側に投入する",
"3. を固定する"
],
"WorkPoints": [
"REAR",
"6/7K302をﾌﾛﾝﾄ側に投入する",
"ここから投入する",
"3K351",
"4K351",
"OPT1K311",
"OPT2K311"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :6.Power Unit確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"検査表②:IO1 ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認",
"検査表②:IO2 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"WEPJ-G002-D05"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D05",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌｧｲﾊﾞｰ線投入・接続",
"WorkItems": [
"2. を接続する",
"1. をﾌﾛﾝﾄ側に投入する",
"3. を固定する"
],
"WorkPoints": [
"REAR",
"6/7K302をﾌﾛﾝﾄ側に投入する",
"ここから投入する",
"3K351",
"4K351",
"OPT1K311",
"OPT2K311"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :6.Power Unit確認",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"検査表②:IO1 ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認",
"検査表②:IO2 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "9.8N･m",
"WorkName": "LCRﾒｰﾀｰ取付け",
"WorkItems": [
"1. 本体にCOLLAR をBOLT WASHER で取付ける",
"2. 本体に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"FRONT",
"前作業にて取付けたｶﾗｰ部に挿入する"
],
"Tolks": [
"締付ﾄﾙｸ 9.8N･m",
"締付ﾄﾙｸ 9.8N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "9.8N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. をLCRﾒｰﾀｰに接続する"
],
"WorkPoints": [
"FRONT",
"仕様により接続本数が違います",
"前側のみ仕様時",
"後側のみ仕様時",
"前後仕様時",
"CH1B4010",
"CH2B4010",
"CH2B4010",
"CH1B4010"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :LCR2 LCRﾒｰﾀｰ部ｺﾈｸﾀ接続確認",
"検査表 :LCR3 LCRﾒｰﾀｰ部ﾈｼﾞ締め付けﾄﾙｸ確認",
"■安全作業",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "精密ﾏｲﾅｽ",
"ToolOther": "15cN･m",
"WorkName": "ｶﾒﾗﾘﾝｸｹｰﾌﾞﾙ接続",
"WorkItems": [
"■1. をLCRﾒｰﾀｰに接続する"
],
"WorkPoints": [
"FRONT",
"仕様により接続本数が違います",
"前側のみ仕様時",
"後側のみ仕様時",
"前後仕様時",
"CH1B4010",
"CH2B4010",
"CH2B4010",
"CH1B4010"
],
"Tolks": [
"締付ﾄﾙｸ 15cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :LCR2 LCRﾒｰﾀｰ部ｺﾈｸﾀ接続確認",
"検査表 :LCR3 LCRﾒｰﾀｰ部ﾈｼﾞ締め付けﾄﾙｸ確認",
"■安全作業",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 各配線を引き回し､固定する"
],
"WorkPoints": [
"FRONT",
"ﾘｱ側へEX122CONTB4012",
"ﾘｱ側へLCRLAN",
"ﾌﾛﾝﾄ側へLCRUSBCONTB4011"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)"
]
}
|
{
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷基板配線接続・引き回し",
"WorkItems": [
"1. CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"REAR",
"LCVLIOK351",
"CNTCRK351",
"CNSPOT1K351",
"CNIOAK351",
"CN32K351",
"CNCOVK351",
"CNCLRK351",
"CN31K351",
"前側より LCRLAN連結ﾌﾞﾗｹｯﾄへ",
"B1324/5/6P/B1344P/1R4310P前側へ",
"DX122ﾊﾟﾜｰﾕﾆｯﾄへ",
"B1337P/B1340/1/2P/1R4345P架台左側へ",
"前後仕様時:CABLE CABLE CABLE ",
"前側仕様時のみ:CABLE CABLE ",
"後側仕様時のみ:CABLE CABLE ",
"『3』を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表CABLE :IO1 ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認",
"検査表CABLE :LCR1 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾘﾝｸﾞI/O負荷基板配線接続・引き回し",
"WorkItems": [
"1. CABLE CABLE CABLE を接続し引き回す"
],
"WorkPoints": [
"REAR",
"LCVLIOK351",
"CNTCRK351",
"CNSPOT1K351",
"CNIOAK351",
"CN32K351",
"CNCOVK351",
"CNCLRK351",
"CN31K351",
"前側より LCRLAN連結ﾌﾞﾗｹｯﾄへ",
"B1324/5/6P/B1344P/1R4310P前側へ",
"DX122ﾊﾟﾜｰﾕﾆｯﾄへ",
"B1337P/B1340/1/2P/1R4345P架台左側へ",
"前後仕様時:CABLE CABLE CABLE ",
"前側仕様時のみ:CABLE CABLE ",
"後側仕様時のみ:CABLE CABLE ",
"『3』を確認する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表CABLE :IO1 ﾘﾝｸﾞI/O基板ｺﾈｸﾀ接続確認",
"検査表CABLE :LCR1 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. 各配線を引き回し､固定する"
],
"WorkPoints": [
"B1337P/B1340/1/2P/1R4345P抜き穴から出しておく",
"DX122EX122",
"CONTB4012抜き穴から出しておく",
"DX122",
"EX122",
"REAR",
"固定は既存ｲﾝｼｭﾛｯｸに固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"検査表①:IO2 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"検査表①:LCR1 ﾊﾟﾜｰﾕﾆｯﾄ部ｺﾈｸﾀ接続確認",
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. 配線を引き回し､固定する"
],
"WorkPoints": [
"FRONT",
"B1324/5/6P/B1344P/1R4310P抜き穴から出しておく",
"抜き穴から出しておくLCRUSBCONTB4011",
"固定は既存ｲﾝｼｭﾛｯｸに固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
}
|
{
"QualityItem": "引き回確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り引き回出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し4",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WEPJ-G002-A03"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-A03",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "黒ｶﾊﾞｰﾗﾍﾞﾙ貼付け1",
"WorkItems": [
"2. 1完成品のLABEL にLABEL を添付する",
"3. SCREW を2完成品と一緒に払出しする",
"1. COVER にLABEL LABEL LABEL LABEL を貼付ける"
],
"WorkPoints": [
"ﾋﾞｽ×9個",
"貼付けはしないこと ※台紙のまま添付のみ",
"指示寸法±1mmに貼付けのこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"30mm",
"100mm",
"158mm",
"5mm",
"272mm",
"200mm",
"56mm"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "黒ｶﾊﾞｰﾗﾍﾞﾙ貼付け2",
"WorkItems": [
"2. COVER にLABEL LABEL を貼付ける",
"3. COVER にLABEL を貼付ける",
"2. COVER にLABEL LABEL を貼付ける",
"3. COVER にLABEL を貼付ける"
],
"WorkPoints": [
"裏側に貼付けのこと",
"指示寸法±1mmに貼付けのこと",
"指示寸法±1mmに貼付けのこと",
"表側に貼付けのこと",
"裏側に貼付けのこと",
"指示寸法±1mmに貼付けのこと",
"指示寸法±1mmに貼付けのこと",
"表側に貼付けのこと"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"5mm",
"272mm",
"200mm",
"56mm",
"20mm",
"150mm",
"5mm",
"272mm",
"200mm",
"56mm",
"20mm",
"150mm"
]
}
|
{
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "寸法の位置に貼付けている事指示寸法±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品払い出し",
"WorkItems": [
"1. COVER SCREW をH2工程に払い出す"
],
"WorkPoints": [
"ﾋﾞｽ×4個"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品付属品",
"WorkItems": [
"1. BRACKET BRACKET BOLT CAP CASE CAUTION SHEET (MAINTENANCE) NOZZLE SHAFT CLEANING TOOL(SILICON TYPE):FC GREASE をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ｽﾙｰ部品ﾕﾆｯﾄ交換工具:NPM-GSeries",
"WorkItems": [
"1. 手配がある場合WRENCH BIT WRENCH HOSE をH2工程に払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材が準備出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "68cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立1",
"WorkItems": [
"2. 1完成品にPULLEY を取付ける",
"3. 2完成品にPULLEY をNUT で仮取付ける",
"4. 3完成品にPULLEY を取付ける",
"2. 1完成品にPULLEY を取付ける",
"3. 2完成品にPULLEY をNUT で仮取付ける",
"4. 3完成品にPULLEY を取付ける"
],
"WorkPoints": [
"下記は右側延長用(左側延長時は左右対称となります)",
"下記は右側延長用(左側延長時は左右対称となります)"
],
"Tolks": [
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m",
"締付ﾄﾙｸ 68cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"仮止め:SD-A033501-140にて本締め",
"仮止め:SD-A033501-140にて本締め"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "68cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "11㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業が出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立2",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業が出来ている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "11㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り作業が出来ている事",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.5㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立3",
"WorkItems": [
"1. にPLATE をBOLT で取付ける",
"2. 1完成品にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"面位置",
"面位置"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"11㎜"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業が出来ている事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "-",
"StdVal": "段差:2.8±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"Size": "",
"ToolOther": "FM-2845",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立4",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "段差確認",
"ToolManageNo": "FM-2845",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "段差:2.8±0.2㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立5",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾉｷﾞｽ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立5",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "段差確認",
"ToolManageNo": "-",
"ToolCycle": "1回/年",
"ToolRecord": "-",
"StdVal": "段差:2.8±0.2㎜",
"Method": "ﾉｷﾞｽ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "基板ｶﾞｲﾄﾞ位置出し治具(待機部)",
"Size": "",
"ToolOther": "FM-2845",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立5",
"WorkItems": [
"1. にGUIDE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"治具で段差を調整する",
"段差:2.8±0.2㎜"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "段差確認",
"ToolManageNo": "FM-2845",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "段差:2.8±0.2㎜",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立6",
"WorkItems": [
"2. 1完成品にCLIP をBOLT で取付ける",
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"ﾚｰﾝ1固定側",
"ﾚｰﾝ2固定側",
"下記は右側延長用(左側延長時は左右対称となります)"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立6",
"WorkItems": [
"3. 2完成品にLABEL LABEL ⑧を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"40㎜",
"20㎜",
"20㎜",
"80㎜",
"28㎜",
"40㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰﾚｰﾙ組立7",
"WorkItems": [
"2. 1完成品にCLIP をBOLT で取付ける",
"1. にCABLE-SUPPORT を取付ける"
],
"WorkPoints": [
"下記は右側延長用(左側延長時は左右対称となります)",
"ﾚｰﾝ2可動側",
"ﾚｰﾝ1可動側"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立1",
"WorkItems": [
"1. COVER にLABEL を貼付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立2",
"WorkItems": [
"1. COVER にCABLE-SUPPORT を取付ける",
"2. 1完成品にｲﾝｼｭﾛｯｸを挿入する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けできている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立3",
"WorkItems": [
"1. にSPACER をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立4",
"WorkItems": [
"1. にSLIDE-PACK をSCREW で取付ける"
],
"WorkPoints": [
"矢印方向に押し当て",
"ﾗﾍﾞﾙが図から見て左側方向で取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "160cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立5",
"WorkItems": [
"1. にBRACKET をSCREW で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 160cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "160cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立5",
"WorkItems": [
"2. 1完成品にLABEL を貼付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ取付け位置ｾﾝﾀｰより 66㎜"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"18.5㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立6",
"WorkItems": [
"1. にCONNECTOR をBOLT で取付ける"
],
"WorkPoints": [
"MOLEX",
"MOLEX",
"MOLEX表示"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立7",
"WorkItems": [
"1. にCABLE CABLE を差込む"
],
"WorkPoints": [
"1B1900L/R",
"1B1900R/L",
"B1900/1P",
"B1900/1TP"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けできている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立8",
"WorkItems": [
"1. にCABLE CABLE を接続し固定する"
],
"WorkPoints": [
"CNEXR/",
"CNEXL/",
"下記は右側延長用",
"下記は左側延長用",
"CNEXR/",
"CNEXL/",
"1B1900R",
"1B1900L",
"1B1900R",
"1B1900L"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :接続確認",
"WEPJ-G002-C05"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C05",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立9",
"WorkItems": [
"1. にLABEL LABEL ⑧を貼付ける"
],
"WorkPoints": [
"貼付け位置"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"10㎜",
"68㎜",
"5㎜",
"5㎜",
"10㎜",
"46㎜",
"10㎜",
"10㎜",
"20㎜",
"68㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "110cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立10",
"WorkItems": [
"1. に を取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立11",
"WorkItems": [],
"WorkPoints": [
"右側",
"左側",
"左側",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"180㎜",
"450㎜",
"340㎜"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±1.0㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立11",
"WorkItems": [],
"WorkPoints": [
"右側",
"左側",
"左側",
"右側"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"180㎜",
"450㎜",
"340㎜"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰｶﾊﾞｰ組立11",
"WorkItems": [
"1. CABLE に下記指示寸法通りのﾏｰｷﾝｸﾞを入れる",
"2. に1完成品を接続しCLIP BOLT WASHER WASHER で固定する"
],
"WorkPoints": [
"右側",
"左側",
"左側",
"CNEXRを接続",
"CNEXL",
"CNEXR",
"CNEXLを接続",
"右側",
"ﾏｰｷﾝｸﾞ位置で固定する事"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"180㎜",
"450㎜",
"180㎜",
"340㎜",
"検査表 :ｺﾈｸﾀ接続確認",
"WEPJ-G002-C05"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-C05",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "延長ｺﾝﾍﾞﾔｰ(ｽﾙｰ部品)",
"WorkItems": [
"1. BRACKET SCREW BRACKET BOLT BRACKET BRACKET COVER BOLT を払い出す",
"2. BELT BELT を払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "ｽﾙｰ部品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの部材がある事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "150cN･m",
"WorkName": "ｽﾄｯﾊﾟｰ組立",
"WorkItems": [
"1. PLATE にSTOPPER をSPACER BOLT WASHER で取付"
],
"WorkPoints": [
"PLATE はねじ穴が2つある面を上にして取付の事",
"ﾃｰﾊﾟｰ面"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "200cN･m",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"WorkItems": [
"2. に をBOLT WASHER で取付"
],
"WorkPoints": [
"傾きの低い方が内側",
"低い方",
"74mm",
"73.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 200cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
" 取付け方向に注意!この部品には方向性があります｡"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ｽﾄｯﾊﾟｰ取付",
"WorkItems": [
"1. のオレンジ四角部分を㉖でふき取る"
],
"WorkPoints": [
"134mm",
"214mm",
"15mm",
"15mm",
"134mm",
"214mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "拭き取り確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "各指示寸法:±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾍﾞｱ取付け",
"WorkItems": [
"1. をNUT-PLATE BOLT WASHER WASHER NUT で取付ける"
],
"WorkPoints": [
"矢印方向に押し当てて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ配線引き回し1",
"WorkItems": [
"1. ﾍﾞｱ配線を引き回す"
],
"WorkPoints": [
"ｽﾍﾟｰｻｰに固定する",
"ﾘﾌﾄを上下させ干渉が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
}
|
{
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "50cN･m",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [
"3. 配線の引き回し･接続を行う"
],
"WorkPoints": [
"ﾅｯﾄを挿入し取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表BRACKET :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ3"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [
"1. BRACKET にﾓｰﾀ動力線をBOLT WASHER NUT で取付ける",
"2. 1完成品をBOLT WASHER で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾍﾞｱ配線引き回し2",
"WorkItems": [
"1. BRACKET にﾓｰﾀ動力線をBOLT WASHER NUT で取付ける",
"2. 1完成品をBOLT WASHER で取付ける",
"3. 配線の引き回し･接続を行う"
],
"WorkPoints": [
"ﾅｯﾄを挿入し取付ける",
"ﾓｰﾀ動力線･ｴﾝｺｰﾀﾞ線引き回し詳細",
"M402P/R",
"B1302P/R",
"B1322P/R",
"E402P/R",
"B1303P/R"
],
"Tolks": [
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(150mm)",
"ｲﾝｼｭﾛｯｸ(150mm×4)",
"検査表BRACKET :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ3",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 配線を引き回し固定する",
"2. 配線引き回し終了後､配線押さえを固定する"
],
"WorkPoints": [
"A矢視",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄに干渉し無い事",
"B401R",
"M401R",
"E401P/R",
"1B1320R",
"B1301R"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "2.5㎜",
"ToolOther": "1.5N･m",
"WorkName": "配線引き回し1",
"WorkItems": [
"1. 配線を引き回し固定する",
"2. 配線引き回し終了後､配線押さえを固定する"
],
"WorkPoints": [
"A矢視",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄに干渉し無い事",
"E401P/R"
],
"Tolks": [
"締付ﾄﾙｸ 1.5N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.5N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. 配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"R401",
"R402",
"R403",
"R404",
"S01R",
"S301P/R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表①:ｺﾈｸﾀ接続確認ﾁｪｯｸ1･5",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. ﾍﾞｱ配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"CN32K302",
"CN33K302",
"CNP3BK401",
"CN2BK401",
"CNP3BK401",
"CN2BK401",
"CN32/33K302"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表①:3-1.ﾓｰﾀﾄﾞﾗｲﾊﾞ接続確認",
"検査表①:3-3.HCOM-IO基板接続確認",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し4",
"WorkItems": [
"1. 補給･ｼｬｯﾀｰの配線を引き回しｺﾈｸﾀを接続する"
],
"WorkPoints": [
"1S01R",
"CN30K302"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表①:3-3.HCOM-IO基板接続確認",
"検査表①:4.ｺﾈｸﾀ接続確認ﾁｪｯｸ6",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定1",
"WorkItems": [
"1. 配線を固定する"
],
"WorkPoints": [
"余長配線を丸めて固定する",
"配管と一緒に固定する",
"TP軸動力線のみ固定",
"配管と一緒に固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
}
|
{
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定2",
"WorkItems": [
"1. 配線を固定する"
],
"WorkPoints": [
"TP軸動力線のみ固定",
"動力線同士を固定する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
}
|
{
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "600㎜",
"ToolOther": "",
"WorkName": "配線固定3",
"WorkItems": [
"1. の配管の先端から340㎜の位置にﾏｰｷﾝｸﾞする",
"2. 1完成品の配線･配管を固定する"
],
"WorkPoints": [
"電源線",
"信号線",
"配管",
"それぞれの黄色ﾏｰｷﾝｸﾞ位置で固定する",
"配管先端"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:±5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線固定3",
"WorkItems": [
"1. の配管の先端から340㎜の位置にﾏｰｷﾝｸﾞする",
"2. 1完成品の配線･配管を固定する"
],
"WorkPoints": [
"電源線",
"信号線",
"配管",
"それぞれの黄色ﾏｰｷﾝｸﾞ位置で固定する",
"配管先端"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"ｲﾝｼｭﾛｯｸ(100mm)"
]
}
|
{
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り結束出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "7㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. に を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "FAN取付け",
"WorkItems": [
"1. に を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "FAN取付け",
"WorkItems": [
"1. に を取付ける",
"2. 1完成品の配線を引き回し､ｺﾈｸﾀを接続する"
],
"WorkPoints": [
"前準備で取付けたﾎﾞﾙﾄ･ﾜｯｼｬｰを使用して取付ける",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄへの干渉無き事",
"G101R"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :4.ｺﾈｸﾀ接続確認ﾁｪｯｸ1",
"WEPJ-G002-D33"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D33",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品払い出し",
"WorkItems": [
"1. BRACKET ~BOLT をﾄﾚｲ本体に付属して払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "部材確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部材が揃っている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付①",
"WorkItems": [
"2. SPACER に1完成品をBOLT で取付",
"■1. LOAD-CELL の型式､製造番号を確認"
],
"WorkPoints": [
"***-****",
"ﾛｰﾄﾞｾﾙの配線を図の向きにて取付",
"向き有 ﾀｯﾌﾟ穴注意"
],
"Tolks": [
"締付ﾄﾙｸ 41cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"※型式:『TC-USR(T)20N25708』と 記載されている事を確認のこと｡",
"※ｼﾘｱﾙ番号を上記項目へ 転記のこと｡",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"■安全作業",
"検査表SPACER :型式･検査書ﾁｪｯｸ",
"WEPJ-G002-D12"
]
}
|
{
"QualityItem": "型式･製造番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D12",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "1.5㎜",
"ToolOther": "41cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付①",
"WorkItems": [
"2. SPACER に1完成品をBOLT で取付",
"■1. LOAD-CELL の型式､製造番号を確認"
],
"WorkPoints": [
"***-****",
"ﾛｰﾄﾞｾﾙの配線を図の向きにて取付",
"向き有 ﾀｯﾌﾟ穴注意"
],
"Tolks": [
"締付ﾄﾙｸ 41cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"※型式:『TC-USR(T)20N25708』と 記載されている事を確認のこと｡",
"※ｼﾘｱﾙ番号を上記項目へ 転記のこと｡",
"この作業では同じものを2個製作",
"この作業では同じものを2個製作",
"■安全作業",
"検査表SPACER :型式･検査書ﾁｪｯｸ",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "41cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾛｰﾄﾞｾﾙ部取付②",
"WorkItems": [
"1. にCOVER SPACER をBOLT WASHER で取付"
],
"WorkPoints": [
"COVER のｶﾊﾞｰとﾛｰﾄﾞｾﾙが干渉しないように取付",
"認識ﾏｰｸが図の位置にくるように取付"
],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部取付①",
"WorkItems": [
"1. SHAFT にSCREW を取付",
"2. 1完成品にBLOCK を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ｼｬﾌﾄ部取付②",
"WorkItems": [
"2. 1完成品を平行に取付"
],
"WorkPoints": [
"P004にﾌﾞﾛｯｸｹﾞｰｼﾞを挟み､BOLT を固定し､ｶﾞﾀつきが無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"Size": "15.5㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部取付②",
"WorkItems": [
"2. 1完成品を平行に取付"
],
"WorkPoints": [
"P004にﾌﾞﾛｯｸｹﾞｰｼﾞを挟み､BOLT を固定し､ｶﾞﾀつきが無い事"
],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "1回/3年",
"ToolRecord": "校正成績書",
"StdVal": "指示通り取付の事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｼｬﾌﾄ部取付③",
"WorkItems": [
"1. に を取付",
"2. 1完成品にCLIP をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"この作業では同じものを2個製作",
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "110cN･m",
"WorkName": "ｼｬﾌﾄ部取付③",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｼｬﾌﾄ部配線",
"WorkItems": [
"1. にｲﾝｼｭﾛｯｸを取付"
],
"WorkPoints": [
"P002下面から24±3mm",
"青丸部分は線が張りすぎないよう取付の事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ(100mm)",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"この作業では同じものを2個製作"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "24±3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "48cN･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ部取付(Front用)",
"WorkItems": [
"1. BRACKET にCABLE をBOLT で取付"
],
"WorkPoints": [
"取付け方向に注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 48cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "48cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2㎜",
"ToolOther": "48cN･m",
"WorkName": "ｺﾈｸﾀﾌﾞﾗｹｯﾄ部取付(Rear用)",
"WorkItems": [
"1. BRACKET にCABLE をBOLT で取付"
],
"WorkPoints": [
"取付け方向に注意すること"
],
"Tolks": [
"締付ﾄﾙｸ 48cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "48cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "製造番号・型式確認(Front用)",
"WorkItems": [
"■1. LOAD-CELL-AMP の型式･製造番号を確認し､検査表に記入"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表LOAD-CELL-AMP :型式･検査書ﾁｪｯｸ",
"■安全作業",
"WEPJ-G002-D12"
]
}
|
{
"QualityItem": "型式･製造番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D12",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "製造番号・型式確認(Rear用)",
"WorkItems": [
"■1. LOAD-CELL-AMP の型式･製造番号を確認し､検査表に記入"
],
"WorkPoints": [
"型式",
"製造番号"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表LOAD-CELL-AMP :型式･検査書ﾁｪｯｸ",
"■安全作業",
"WEPJ-G002-D12"
]
}
|
{
"QualityItem": "型式･製造番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認製造番号転記",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D12",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "ｱﾝﾌﾟ取付(Front用)",
"WorkItems": [
"1. TERMINAL-SUPPORT をRAIL に取付",
"4. に を取付"
],
"WorkPoints": [
"緑○部がしっかりはまっている事",
"12mm",
"付属ﾈｼﾞで取付",
"8.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱﾝﾌﾟ取付(Front用)",
"WorkItems": [
"1. TERMINAL-SUPPORT をRAIL に取付",
"4. に を取付",
"2. SPACER にSCREW を取付",
"3. 2完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"緑○部がしっかりはまっている事",
"12mm",
"付属ﾈｼﾞで取付",
"8.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "110cN･m",
"WorkName": "ｱﾝﾌﾟ取付(Rear用)",
"WorkItems": [
"1. TERMINAL-SUPPORT をRAIL に取付",
"4. に を取付"
],
"WorkPoints": [
"12mm",
"付属ﾈｼﾞで取付",
"8.5mm"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "110cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ｱﾝﾌﾟ取付(Rear用)",
"WorkItems": [
"1. TERMINAL-SUPPORT をRAIL に取付",
"4. に を取付",
"2. SPACER にSCREW を取付",
"3. 2完成品にCABLE-SUPPORT を取付"
],
"WorkPoints": [
"12mm",
"付属ﾈｼﾞで取付",
"8.5mm",
"緑○部がしっかりはまっている事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "69cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(Front用)",
"WorkItems": [
"■3. 2完成品にCABLE を取付",
"■2. 1完成品にCABLE を取付",
"■1. に の配線を取付"
],
"WorkPoints": [
"ｱﾝﾌﾟ表示名とﾏｰｸﾁｭｰﾌﾞ名が同じところに接続する事",
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"奥まで差込み､抜けないか確認"
],
"Tolks": [
"締付ﾄﾙｸ 69cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"■安全作業",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "69cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(Front用)",
"WorkItems": [
"■2. 1完成品にCABLE を取付",
"■1. に の配線を取付"
],
"WorkPoints": [
"ｱﾝﾌﾟ表示名とﾏｰｸﾁｭｰﾌﾞ名が同じところに接続する事",
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"奥まで差込み､抜けないか確認"
],
"Tolks": [
"締付ﾄﾙｸ 69cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "69cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(Rear用)",
"WorkItems": [
"■3. 2完成品にCABLE を取付",
"■2. 1完成品にCABLE を取付",
"■1. に の配線を取付"
],
"WorkPoints": [
"奥まで差込み､軽く電線を引いて､確実にｸﾗﾝﾌﾟされていることを確認",
"ｱﾝﾌﾟ表示名とﾏｰｸﾁｭｰﾌﾞ名が同じところに接続する事",
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"各ﾋﾟﾝに付いているﾎﾞﾀﾝ(黒い部分)を押しながら電線を差込穴に差込む｡",
"電線差込穴"
],
"Tolks": [
"締付ﾄﾙｸ 69cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"■安全作業",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "69cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "50cN･m",
"WorkName": "ｱﾝﾌﾟ端子接続(Rear用)",
"WorkItems": [
"■2. 1完成品にCABLE を取付",
"■1. に の配線を取付"
],
"WorkPoints": [
"ｱﾝﾌﾟ表示名とﾏｰｸﾁｭｰﾌﾞ名が同じところに接続する事",
"ﾏｰｸﾁｭｰﾌﾞ番号と同じところに挿入",
"各ﾋﾟﾝに付いているﾎﾞﾀﾝ(黒い部分)を押しながら電線を差込穴に差込む｡",
"電線差込穴"
],
"Tolks": [
"締付ﾄﾙｸ 69cN･m",
"締付ﾄﾙｸ 50cN･m",
"締付ﾄﾙｸ 50cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :棒端子･丸端子 接続確認",
"検査表 :ﾈｼﾞ締めﾄﾙｸ",
"■安全作業"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "50cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "荷重ﾁｪｯｶｰ用24V電源ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6261",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟ通信設定確認",
"WorkItems": [
"4. ㉖でプログラム（TD-SC1 Setup）を起動する",
"3. （ ）のコネクタに㉘をつなぎ電源を入れる",
"2. （ ）と㉖を㉗で繋ぐ（黄丸）",
"1. ( )のｽｲｯﾁを右図のようにUSB(下側)に変更する(黄矢印)"
],
"WorkPoints": [
"ｱﾝﾌﾟに電源が入ると下のﾗﾝﾌﾟ点灯(青丸)"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"WEPJ-G002-D12"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "FM-6261",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D12",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定",
"WorkItems": [
"1. ｽｲｯﾁ設定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定",
"WEPJ-G002-D12"
]
}
|
{
"QualityItem": "設定確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り設定出来ている事",
"Method": "目視",
"RecordMethod": "WEPJ-G002-D12",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定",
"WorkItems": [
"1. ｽｲｯﾁ設定"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾛｰﾄﾞｾﾙｱﾝﾌﾟのｽｲｯﾁ設定"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "払い出し部品",
"WorkItems": [
"1. 次工程に払い出し"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"Front用",
"Rear用"
]
}
|
{
"QualityItem": "部品準備",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した部品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
End of preview. Expand
in Data Studio
No dataset card yet
- Downloads last month
- 18