input
stringclasses 1
value | instruction
stringlengths 202
3.29k
| output
stringlengths 193
312
| category
stringclasses 1
value | index
stringclasses 1
value | fileName
null |
|---|---|---|---|---|---|
{
"ToolName": "ﾍﾞﾙﾄﾃﾝｼｮﾝｼﾞｸﾞ:G10",
"Size": "",
"ToolOther": "FM-6591",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ調整2、ｽﾄｯﾊﾟ取付",
"WorkItems": [],
"WorkPoints": [
"40mm",
"調整後締結",
"質量:2.5g幅 :12mmｽﾊﾟﾝ:80mm規格:59N±10%",
"ﾌﾟｰﾘを手で回し数回測定する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"測定箇所",
"検査表 :ﾍﾞﾙﾄﾃﾝｼｮﾝ測定"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-6591",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "4㎜",
"ToolOther": "6.0N･m",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ調整2、ｽﾄｯﾊﾟ取付",
"WorkItems": [],
"WorkPoints": [
"40mm",
"調整後締結",
"質量:2.5g幅 :12mmｽﾊﾟﾝ:80mm規格:59N±10%",
"ﾌﾟｰﾘを手で回し数回測定する事"
],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"測定箇所",
"検査表 :ﾍﾞﾙﾄﾃﾝｼｮﾝ測定"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ調整2、ｽﾄｯﾊﾟ取付",
"WorkItems": [
"1. のﾓｰﾀﾍﾞﾙﾄ張力調整",
"2. 1完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
"㉛のハンドルを青矢印方向に引き、㉛の橙線をブロックの橙線部にはめる",
"調節ﾈｼﾞ",
"㉛のハンドルを青矢印方向に押す、調節ネジをねじ込みモータを押し上げる",
"㉛使用方法"
],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ連結",
"WorkItems": [
"1. のﾍﾞﾙﾄをBLOCK PLATE で挟んでBOLT で取付",
"2. 1で取付けたBLOCK PLATE を駆動ﾌﾟﾚｰﾄにBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m",
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ連結",
"WorkItems": [
"1. のﾍﾞﾙﾄをBLOCK PLATE で挟んでBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "3㎜",
"ToolOther": "3.2N･m",
"WorkName": "ﾀｲﾐﾝｸﾞﾍﾞﾙﾄ連結",
"WorkItems": [
"2. 1で取付けたBLOCK PLATE を駆動ﾌﾟﾚｰﾄにBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 3.2N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "駆動部ｾﾝｻ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. 1完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
"長穴ｾﾝﾀｰで取付ける",
"長穴ｾﾝﾀｰで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "駆動部ｾﾝｻ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. 1完成品に をBOLT WASHER で取付"
],
"WorkPoints": [
"長穴ｾﾝﾀｰで取付ける",
"長穴ｾﾝﾀｰで取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "引込みｱｰﾑ下ﾌﾞﾛｯｸ取付",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付"
],
"WorkPoints": [
"A矢視図",
" のﾋﾟﾝを に入れる",
"軽く動く程度に緩めておく"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"仮止め:全体組立調整工程にて本締め"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "左引込みｱｰﾑ取付",
"WorkItems": [
"1. のﾎﾞﾙﾄに COLLAR COLLAR COLLAR を入れNUT WASHER WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "左引込みｱｰﾑ取付",
"WorkItems": [
"1. のﾎﾞﾙﾄに COLLAR COLLAR COLLAR を入れNUT WASHER WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "右引込みｱｰﾑ取付",
"WorkItems": [
"1. のﾎﾞﾙﾄに COLLAR COLLAR COLLAR を入れNUT WASHER WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "右引込みｱｰﾑ取付",
"WorkItems": [
"1. のﾎﾞﾙﾄに COLLAR COLLAR COLLAR を入れNUT WASHER WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ｱｰﾑ連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ BOLT 150cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "5.5㎜",
"ToolOther": "3.6N･m",
"WorkName": "ｱｰﾑ連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ BOLT 150cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "150cN･m",
"WorkName": "ｱｰﾑ連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ BOLT 150cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "G10ﾄﾚｲﾌｨｰﾀﾞ引き出し部ﾌﾞﾛｯｸ角度位置決めｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-6615",
"WorkName": "ｱｰﾑ連結",
"WorkItems": [],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ BOLT 150cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-6615",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ｱｰﾑ連結",
"WorkItems": [
"1. SHAFT にBEARING を入れE-RING で取付",
"2. SHAFT を ｱｰﾑの間に入れPLATE を挟み1完成品､BOLT WASHER で取付"
],
"WorkPoints": [
"・㉜をアームのピンク線に\u3000\u3000合わせ上のネジで固定・PLATE 上面（緑線）を㉜に当てつけて固定・反対側も同様に行う",
"0.1mmｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"㉜でPLATE の位置決めをして固定"
],
"Tolks": [
"締付ﾄﾙｸ BOLT 150cN･m",
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾈｼﾞ",
"この作業では同じものを2個製作",
"検査表SHAFT :認識穴角度調整",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付",
"2. 1完成品に をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾌﾞﾗｹｯﾄ取付",
"WorkItems": [
"2. 1完成品に をBOLT WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾓｰﾀ配線引き回し",
"WorkItems": [
"1. のモータ配線を㉖で固定する"
],
"WorkPoints": [
"穴から下に降ろす"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
}
|
{
"QualityItem": "結束確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "配線･配管に負荷無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動ｾﾝｻ配線引き回し",
"WorkItems": [
"1. にCABLE を接続する"
],
"WorkPoints": [
"穴から降ろす",
"B1323R",
"B1324R",
"B1322R",
"B1325R",
"可動部に干渉無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ｺﾈｸﾀ挿入確認",
"検査表 :配線関係",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "駆動ｾﾝｻ配線引き回し",
"WorkItems": [
"1. にCABLE を接続する"
],
"WorkPoints": [
"穴から降ろす",
"B1323R",
"B1324R",
"B1322R",
"B1325R",
"可動部に干渉無き事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ｺﾈｸﾀ挿入確認",
"検査表 :配線関係",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "配線･配管干渉確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ｶﾞｲﾄﾞ部ﾎﾟｽﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "5㎜",
"ToolOther": "6.0N･m",
"WorkName": "ｶﾞｲﾄﾞ部ﾎﾟｽﾄ取付",
"WorkItems": [
"1. に をBOLT WASHER WASHER で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 6.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "6.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ｶﾞｲﾄﾞ部仮取付",
"WorkItems": [
"1. に をBOLT WASHER で仮取付",
"1. に をBOLT WASHER で仮取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ｶﾞｲﾄﾞ部高さ調整",
"WorkItems": [
"1. のｶﾞｲﾄﾞﾌﾞﾗｹｯﾄ高さを調整する"
],
"WorkPoints": [
"基準面 166.2mm",
"測定ﾎﾟｲﾝﾄ",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄにて調整後ﾅｯﾄをﾛｯｸする",
"166.2 \u002B0.2/0mmに調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｶﾞｲﾄﾞ高さ測定ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5049",
"WorkName": "ｶﾞｲﾄﾞ部高さ調整",
"WorkItems": [
"1. のｶﾞｲﾄﾞﾌﾞﾗｹｯﾄ高さを調整する"
],
"WorkPoints": [
"基準面 166.2mm",
"測定ﾎﾟｲﾝﾄ",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄにて調整後ﾅｯﾄをﾛｯｸする",
"166.2 \u002B0.2/0mmに調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5049",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"Size": "1/100",
"ToolOther": "",
"WorkName": "ｶﾞｲﾄﾞ部高さ調整",
"WorkItems": [
"1. のｶﾞｲﾄﾞﾌﾞﾗｹｯﾄ高さを調整する"
],
"WorkPoints": [
"基準面 166.2mm",
"測定ﾎﾟｲﾝﾄ",
"ｱｼﾞｬｽﾄﾎﾞﾙﾄにて調整後ﾅｯﾄをﾛｯｸする",
"166.2 \u002B0.2/0mmに調整する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "高さ･平面度確認",
"ToolManageNo": "-",
"ToolCycle": "1回/半年",
"ToolRecord": "校正成績書",
"StdVal": "166.2㎜\u002B0.2/0㎜",
"Method": "てこ式ﾀﾞｲﾔﾙｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整1",
"WorkItems": [
"1. のﾌﾞﾗｹｯﾄとﾊﾟﾚｯﾄｶﾞｲﾄﾞのﾈｼﾞ(青矢印)を緩める"
],
"WorkPoints": [
"反対側も同様に緩める"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. に㉗を取付"
],
"WorkPoints": [
"㉗にクランプアームを入れる",
"A矢視1",
"㉗をリニアガイドにはめる",
"A矢視2",
"A矢視3",
"㉗をパレットガイド面に乗せる",
"この時㉗にガイド（全体図 青丸）がついているので乗り上げないように注意",
"㉗にピンがあるのでプレートの溝に合わせ緑矢印方向に当てる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. に㉗を取付"
],
"WorkPoints": [
"㉗にクランプアームを入れる",
"A矢視1",
"㉗をリニアガイドにはめる",
"A矢視2",
"A矢視3",
"㉗をパレットガイド面に乗せる",
"この時㉗にガイド（全体図 青丸）がついているので乗り上げないように注意",
"㉗にピンがあるのでプレートの溝に合わせ緑矢印方向に当てる"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. の左右のブラケットを㉗に合わせて固定"
],
"WorkPoints": [
"ブラケットを矢印方向に㉗に押し当て",
"反対も同様に固定",
"隙間0.1mmが入ら無い事",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾌﾞﾗｹｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"検査表 :ｶﾞｲﾄﾞ幅･ｶﾞｲﾄﾞ高さ･ｶﾞｲﾄﾞY方向"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. の左右のブラケットを㉗に合わせて固定"
],
"WorkPoints": [
"ブラケットを矢印方向に㉗に押し当て",
"反対も同様に固定",
"隙間0.1mmが入ら無い事",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾌﾞﾗｹｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"検査表 :ｶﾞｲﾄﾞ幅･ｶﾞｲﾄﾞ高さ･ｶﾞｲﾄﾞY方向"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. の左右のブラケットを㉗に合わせて固定"
],
"WorkPoints": [
"ブラケットを矢印方向に㉗に押し当て",
"反対も同様に固定",
"隙間0.1mmが入ら無い事",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾌﾞﾗｹｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"検査表 :ｶﾞｲﾄﾞ幅･ｶﾞｲﾄﾞ高さ･ｶﾞｲﾄﾞY方向"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整2",
"WorkItems": [
"1. の左右のブラケットを㉗に合わせて固定"
],
"WorkPoints": [
"ブラケットを矢印方向に㉗に押し当て",
"反対も同様に固定",
"隙間0.1mmが入ら無い事",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ﾌﾞﾗｹｯﾄ",
"ﾌﾞﾗｹｯﾄ",
"検査表 :ｶﾞｲﾄﾞ幅･ｶﾞｲﾄﾞ高さ･ｶﾞｲﾄﾞY方向",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅を調整",
"2. ｸﾗﾝﾌﾟｱｰﾑを仮固定"
],
"WorkPoints": [
"ガイドと㉙の隙間に㉚が入ら無い事",
"A矢視図",
"B矢視図"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"ｶﾞｲﾄﾞ押し当て",
"ｶﾞｲﾄﾞ押し当て"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "引き出部ｶﾞｲﾄﾞ平行出し治具",
"Size": "",
"ToolOther": "FM-6386",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅を調整",
"2. ｸﾗﾝﾌﾟｱｰﾑを仮固定"
],
"WorkPoints": [
"ガイドと㉙の隙間に㉚が入ら無い事",
"A矢視図",
"B矢視図"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"ｶﾞｲﾄﾞ押し当て",
"ｶﾞｲﾄﾞ押し当て"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-6386",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅を調整",
"2. ｸﾗﾝﾌﾟｱｰﾑを仮固定"
],
"WorkPoints": [
"ガイドと㉙の隙間に㉚が入ら無い事",
"A矢視図",
"B矢視図"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"ｶﾞｲﾄﾞ押し当て",
"ｶﾞｲﾄﾞ押し当て"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.1㎜",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅調整",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ幅を調整",
"2. ｸﾗﾝﾌﾟｱｰﾑを仮固定"
],
"WorkPoints": [
"ガイドと㉙の隙間に㉚が入ら無い事",
"A矢視図",
"B矢視図"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"ｶﾞｲﾄﾞ押し当て",
"ｶﾞｲﾄﾞ押し当て"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが入ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻｰ取付",
"WorkItems": [
"■1. 型式確認､ﾛｯﾄ番号記入",
"2. にSENSOR をSCREW WASHER WASHER で取付"
],
"WorkPoints": [
"SENSOR は と㉖の下から通してからブラケットに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :検出ｾﾝｻの型式確認とﾛｯﾄNo.記録",
"投光",
"受光",
"■安全作業",
"仮止め:SD-A052466-058にて本締め",
"■安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄ有無ｾﾝｻｰ取付",
"WorkItems": [
"■1. 型式確認､ﾛｯﾄ番号記入",
"2. にSENSOR をSCREW WASHER WASHER で取付"
],
"WorkPoints": [
"SENSOR は と㉖の下から通してからブラケットに取付"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :検出ｾﾝｻの型式確認とﾛｯﾄNo.記録",
"投光",
"受光",
"■安全作業",
"仮止め:SD-A052466-058にて本締め",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "型式確認･製造番号記録",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式･検査書確認､及びｼﾘｱﾙNo.転記",
"Method": "目視",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. に配線を引き回す"
],
"WorkPoints": [
"受光",
"根元からRの先端 15mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"矢視",
"矢視図"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "配線引き回し2",
"WorkItems": [
"1. に配線を引き回す"
],
"WorkPoints": [
"受光",
"根元からRの先端 15mm"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"矢視",
"矢視図"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "15㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"ﾀｸﾞ位置",
"挿入されていること",
"B1304R",
"B1303R",
"B1305R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :ｺﾈｸﾀ挿入確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"ﾀｸﾞ位置",
"挿入されていること",
"B1304R",
"B1303R",
"B1305R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :ｺﾈｸﾀ挿入確認"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "15㎜±1㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "配線引き回し3",
"WorkItems": [
"1. にCABLE を引き回す"
],
"WorkPoints": [
"ﾀｸﾞ位置",
"挿入されていること",
"B1304R",
"B1303R",
"B1305R"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"検査表 :ｺﾈｸﾀ挿入確認",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "配線引き回し4",
"WorkItems": [
"1. に配線を引き回す"
],
"WorkPoints": [
"A矢視図"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認"
],
"WorkPoints": [
"A矢視図",
"隙間がある場合は再調整:SD-A052466-047参照",
"㉘シックネスゲージが通ら無い事",
"反対側も同様に締付",
"反対側も同様に締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｶﾞｲﾄﾞ幅調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5242",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認"
],
"WorkPoints": [
"A矢視図",
"隙間がある場合は再調整:SD-A052466-047参照",
"㉘シックネスゲージが通ら無い事",
"反対側も同様に締付",
"反対側も同様に締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.05㎜",
"ToolOther": "",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認"
],
"WorkPoints": [
"A矢視図",
"隙間がある場合は再調整:SD-A052466-047参照",
"㉘シックネスゲージが通ら無い事",
"反対側も同様に締付",
"反対側も同様に締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜ｼｯｸﾈｽｹﾞｰｼﾞが通ら無い事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "4㎜",
"ToolOther": "3.6N･m",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認"
],
"WorkPoints": [
"A矢視図",
"隙間がある場合は再調整:SD-A052466-047参照",
"㉘シックネスゲージが通ら無い事",
"反対側も同様に締付",
"反対側も同様に締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.6N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"Size": "8㎜",
"ToolOther": "194cN･m",
"WorkName": "ﾊﾟﾚｯﾄｶﾞｲﾄﾞ隙間確認",
"WorkItems": [
"1. のﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度を確認"
],
"WorkPoints": [
"A矢視図",
"隙間がある場合は再調整:SD-A052466-047参照",
"㉘シックネスゲージが通ら無い事",
"反対側も同様に締付",
"反対側も同様に締付"
],
"Tolks": [
"締付ﾄﾙｸ 3.6N･m",
"締付ﾄﾙｸ 194cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"A矢視",
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "中央ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付､確認"
],
"WorkPoints": [
"隙間がある場合は の高さで調整",
"通り:0.1㎜/止まり:0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｶﾞｲﾄﾞ幅調整ｼﾞｸﾞ",
"Size": "",
"ToolOther": "FM-5242",
"WorkName": "中央ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付､確認"
],
"WorkPoints": [
"隙間がある場合は の高さで調整",
"通り:0.1㎜/止まり:0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5242",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "中央ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付､確認"
],
"WorkPoints": [
"隙間がある場合は の高さで調整",
"通り:0.1㎜/止まり:0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.1㎜が通るように調整する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"Size": "0.10㎜",
"ToolOther": "",
"WorkName": "中央ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付､確認"
],
"WorkPoints": [
"隙間がある場合は の高さで調整",
"通り:0.1㎜/止まり:0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認",
"WETE-G002-C24"
]
}
|
{
"QualityItem": "寸法確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "0.15㎜が止まるように調整する事",
"Method": "ｼｯｸﾈｽｹﾞｰｼﾞ",
"RecordMethod": "WETE-G002-C24",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "中央ﾊﾟﾚｯﾄｶﾞｲﾄﾞ取付",
"WorkItems": [
"1. に をBOLT WASHER で取付､確認"
],
"WorkPoints": [
"隙間がある場合は の高さで調整",
"通り:0.1㎜/止まり:0.15㎜"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :ﾊﾟﾚｯﾄｶﾞｲﾄﾞ平面度の確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾚｲﾌｨｰﾀﾞ引き出し部組立台",
"Size": "",
"ToolOther": "FM-5130",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"WorkItems": [
"1. ｾﾝｻの光軸を調整"
],
"WorkPoints": [
"投光",
"受光",
"ｱｰﾑをｽﾄｯﾊﾟｰに当てる",
"光軸",
"光軸",
"ｱｰﾑの穴を通過する事",
"㉗をコネクタ（B1302R）へ接続する事",
"このﾈｼﾞで調整",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-5130",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "PHﾁｪｯｶｰ",
"Size": "",
"ToolOther": "FM-2375",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"WorkItems": [
"1. ｾﾝｻの光軸を調整"
],
"WorkPoints": [
"投光",
"受光",
"ｱｰﾑをｽﾄｯﾊﾟｰに当てる",
"光軸",
"光軸",
"ｱｰﾑの穴を通過する事",
"㉗をコネクタ（B1302R）へ接続する事",
"このﾈｼﾞで調整",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "光軸確認",
"ToolManageNo": "FM-2375",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｱｰﾑの穴を通過する事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "2.5㎜",
"ToolOther": "95cN･m",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"WorkItems": [
"1. ｾﾝｻの光軸を調整"
],
"WorkPoints": [
"投光",
"受光",
"ｱｰﾑをｽﾄｯﾊﾟｰに当てる",
"光軸",
"光軸",
"ｱｰﾑの穴を通過する事",
"㉗をコネクタ（B1302R）へ接続する事",
"このﾈｼﾞで調整",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "194cN･m",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"WorkItems": [
"1. ｾﾝｻの光軸を調整"
],
"WorkPoints": [
"投光",
"受光",
"ｱｰﾑをｽﾄｯﾊﾟｰに当てる",
"光軸",
"光軸",
"ｱｰﾑの穴を通過する事",
"㉗をコネクタ（B1302R）へ接続する事",
"このﾈｼﾞで調整",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "194cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "No.2",
"ToolOther": "40cN･m",
"WorkName": "TP軸ｽﾛｯﾄ位置ﾊﾟﾚｯﾄ有無ｾﾝｻ光軸調整",
"WorkItems": [
"1. ｾﾝｻの光軸を調整"
],
"WorkPoints": [
"投光",
"受光",
"ｱｰﾑをｽﾄｯﾊﾟｰに当てる",
"光軸",
"光軸",
"ｱｰﾑの穴を通過する事",
"㉗をコネクタ（B1302R）へ接続する事",
"このﾈｼﾞで調整",
"反対も同様"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 194cN･m",
"締付ﾄﾙｸ 40cN･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立①",
"WorkItems": [
"1. FRAME にNUT SUPPORT を取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立②",
"WorkItems": [
"1. FRAME にNUT NUT SUPPORT を取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立③",
"WorkItems": [
"1. FRAME にNUT SUPPORT を取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立④",
"WorkItems": [
"1. PANEL にPACKING を取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"PACKING の長い方を内側面に向けて取付ける",
"内側面",
"取手穴",
"内側面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑤",
"WorkItems": [
"1. に FRAME をBLOCK と付属ﾋﾞｽで取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"4角をBLOCK の付属ﾋﾞｽで取付ける",
"内側面",
"取手穴"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑥",
"WorkItems": [
"1. にHINGE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付ける",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"型式",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表BRACKET :安全部品確認",
"WWXJ-5300-012"
]
}
|
{
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-012",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"Size": "",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑦",
"WorkItems": [
"2. BRACKET にSWITCH をNUT-PLATE BOLT WASHER WASHER で取付ける",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"型式",
"ｼﾘｱﾙNo."
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表BRACKET :安全部品確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "各1.0N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑧",
"WorkItems": [
"1. に をBOLT WASHER で取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑨",
"WorkItems": [
"1. にPLATE をBOLT で取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑩",
"WorkItems": [
"1. にBRACKET BRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉FR組立⑪",
"WorkItems": [
"1. にPULL をBOLT WASHER NUT で取付ける"
],
"WorkPoints": [
"2ｾｯﾄ作成",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "300㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立①IC供給有",
"WorkItems": [
"1. FRAME にNUT NUT SUPPORT を取付ける"
],
"WorkPoints": [
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "150㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立②IC供給有",
"WorkItems": [
"1. FRAME にNUT SUPPORT を取付ける"
],
"WorkPoints": [
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立③IC供給有",
"WorkItems": [
"1. PANEL にPACKING を取付ける"
],
"WorkPoints": [
"PACKING の長い方を内側面に向けて取付ける",
"内側面",
"取手穴",
"内側面",
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立④IC供給有",
"WorkItems": [
"1. に FRAME FRAME をBLOCK と付属ﾋﾞｽで取付ける"
],
"WorkPoints": [
"4角をBLOCK の付属ﾋﾞｽで取付ける",
"内側面",
"取手穴",
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立⑤IC供給有",
"WorkItems": [
"2. にKEY COVER をBOLT WASHER WASHER で取付ける",
"■1. KEY の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"IC供給有り",
"型式",
"ｼﾘｱﾙNo.",
"梱包袋のﾗﾍﾞﾙ",
"下寄せで取付",
"調整ﾋﾞｽ"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"■安全作業",
"検査表 :安全部品確認",
"WWXJ-5300-064"
]
}
|
{
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WWXJ-5300-064",
"Other": "-",
"ProcessName": "安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立⑥IC供給有",
"WorkItems": [
"2. 1.完成品にBRACKET をBOLT WASHER で取付ける",
"1. にCATCH をBOLT で取付ける"
],
"WorkPoints": [
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立⑦IC供給有",
"WorkItems": [
"1. にPULL を取付ける"
],
"WorkPoints": [
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ扉R小組立⑧IC供給有",
"WorkItems": [
"1. にHINGE をBOLT WASHER で取付ける"
],
"WorkPoints": [
"IC供給有り"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "移載治具取付",
"WorkItems": [],
"WorkPoints": [
"配線の噛み込み､各部への干渉が無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｺﾝﾍﾞｱﾁｪｯｶｰNPM-W対応",
"Size": "",
"ToolOther": "FM-2222",
"WorkName": "移載治具取付",
"WorkItems": [
"2. ﾁｪｯｶｰに繋いだｺﾈｸﾀを取り外す",
"4. ﾍﾞｰｽ真ん中の四角部分のみ取り外す",
"5. ㉙を取付ける",
"2. ﾁｪｯｶｰに繋いだｺﾈｸﾀを取り外す",
"4. ﾍﾞｰｽ真ん中の四角部分のみ取り外す",
"5. ㉙を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取外確認",
"ToolManageNo": "FM-2222",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取外出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｺﾝﾍﾞｱ移載用ｼﾞｸﾞ(NPM-WX)",
"Size": "",
"ToolOther": "FM-4831",
"WorkName": "ｺﾝﾍﾞﾔｰ取り外し",
"WorkItems": [
"◆3. 運搬台車にｺﾝﾍﾞﾔｰを取付ける",
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞﾔｰを吊り上げる",
"1. ｺﾝﾍﾞﾔｰの取付けﾎﾞﾙﾄを取り外す"
],
"WorkPoints": [
"ﾘｱ側",
"ﾌﾛﾝﾄ側",
"4ヶ所で固定する事",
"治具取付用 M6×20 AW 4本",
"二人作業",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業",
"◆作業者安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4831",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾘﾌﾀｰ",
"Size": "",
"ToolOther": "",
"WorkName": "ｺﾝﾍﾞﾔｰ取り外し",
"WorkItems": [
"◆3. 運搬台車にｺﾝﾍﾞﾔｰを取付ける",
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞﾔｰを吊り上げる",
"1. ｺﾝﾍﾞﾔｰの取付けﾎﾞﾙﾄを取り外す"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"4ヶ所で固定する事",
"治具取付用 M6×20 AW 4本",
"二人作業",
"二人作業"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "重量物運搬",
"ProcessName": "作業者安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾘﾌﾄ用ｱﾀｯﾁﾒﾝﾄ(ﾌｫｰｸﾀｲﾌﾟ)",
"Size": "",
"ToolOther": "FM-3221",
"WorkName": "ｺﾝﾍﾞﾔｰ取り外し",
"WorkItems": [
"◆3. 運搬台車にｺﾝﾍﾞﾔｰを取付ける",
"◆2. ﾘﾌﾀｰでｺﾝﾍﾞﾔｰを吊り上げる",
"1. ｺﾝﾍﾞﾔｰの取付けﾎﾞﾙﾄを取り外す"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"ﾘｱ側",
"二人作業",
"二人作業",
"4ヶ所で固定する事",
"治具取付用 M6×20 AW 4本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-3221",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "基板ｺﾝﾍﾞｱ運搬台車",
"Size": "",
"ToolOther": "FM-4470",
"WorkName": "ｺﾝﾍﾞﾔｰ取り外し",
"WorkItems": [
"◆3. 運搬台車にｺﾝﾍﾞﾔｰを取付ける"
],
"WorkPoints": [
"ﾌﾛﾝﾄ側",
"4ヶ所で固定する事",
"治具取付用 M6×20 AW 4本"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"◆作業者安全作業"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-4470",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "作業者安全工程"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "付属品確認",
"WorkItems": [
"1. BELT BELT BELT を払い出す"
],
"WorkPoints": [],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "付属品確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示した付属品を払い出す事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ｽｹｰﾙ",
"Size": "1000㎜",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立①",
"WorkItems": [
"1. FRAME にSUPPORT NUT を取付ける",
"2. 1.完成品の両端にCAP を取付ける"
],
"WorkPoints": [
"2個製作"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立②",
"WorkItems": [
"1. COVER に をSCREW で取付ける",
"2. 1.完成品にSCREW WASHER を取付ける"
],
"WorkPoints": [
"側面",
"ｻﾞｸﾞﾘ",
" を内側面に取付ける",
"外側面から取付ける",
"側面",
"SCREW ﾈｼﾞを外側面から取付ける",
"外側",
"内側",
"COVER ｶﾊﾞｰを半透明にした状態",
"外側",
"内側",
"COVER のｻﾞｸﾞﾘが有る面が内面"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"外側面",
"外側面"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立③",
"WorkItems": [
"1. にPULL をBOLT WASHER ㉒で取付ける"
],
"WorkPoints": [
"側面",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"外側",
"内側"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"外側面"
]
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立④",
"WorkItems": [
"2. BRACKET にSWITCH をBOLT で取付ける",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. に2.完成品をBOLT WASHER ㉒WASHER で取付ける"
],
"WorkPoints": [
"P1の場合",
"P2の場合",
"側面",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"取手",
"ｽｲｯﾁ",
"外側",
"内側",
" ｶﾊﾞｰを半透明にした状態",
"BOLT ﾈｼﾞを外側面から取付ける",
"内側面に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :安全部品確認",
"検査表②:安全部品確認",
"WWYJ-5300-033"
]
}
|
{
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-033",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "-",
"Size": "",
"ToolOther": "",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立④",
"WorkItems": [
"2. BRACKET にSWITCH をBOLT で取付ける",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する",
"3. に2.完成品をBOLT WASHER ㉒WASHER で取付ける"
],
"WorkPoints": [
"P1の場合",
"P2の場合",
"側面",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"取手",
"ｽｲｯﾁ",
"外側",
"内側",
" ｶﾊﾞｰを半透明にした状態",
"BOLT ﾈｼﾞを外側面から取付ける",
"内側面に取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :安全部品確認",
"検査表②:安全部品確認",
"WWYJ-5300-034"
]
}
|
{
"QualityItem": "型式･ｼﾘｱﾙ番号確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "型式確認ｼﾘｱﾙ番号転記",
"Method": "目視",
"RecordMethod": "WWYJ-5300-034",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"Size": "3㎜",
"ToolOther": "1.0N･m",
"WorkName": "ﾌﾚｰﾑｷｯﾄ(ｶﾊﾞｰREAR)組立④",
"WorkItems": [
"2. BRACKET にSWITCH をBOLT で取付ける",
"■1. SWITCH の型式を確認し､ｼﾘｱﾙNoを検査書に記入する"
],
"WorkPoints": [
"P1の場合",
"P2の場合",
"下記同一Noの部品は各機種毎の部材で同一作業を実施する",
"BOLT ﾈｼﾞを外側面から取付ける"
],
"Tolks": [
"締付ﾄﾙｸ 1.0N･m"
],
"InspectionNo": "",
"InspectionItems": [],
"Words": [
"検査表 :安全部品確認",
"検査表②:安全部品確認"
]
}
|
{
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.0N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "油砥石",
"Size": "",
"ToolOther": "ｽｰﾊﾟｰｼｬｲﾅｰ",
"WorkName": "BASE組立",
"WorkItems": [
"1. BASE に油砥石をかける",
"2. 1.完成品にPIN PIN を圧入する"
],
"WorkPoints": [
"加工面全部に砥石をかける事",
"PIN PIN はﾃｰﾊﾟｰ側から圧入する事",
"ﾊﾞﾘ､ｶｴﾘ､打痕無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ､ｶｴﾘ､打痕無い事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "圧入機",
"Size": "",
"ToolOther": "",
"WorkName": "BASE組立",
"WorkItems": [
"3. 2.完成品にPIN を圧入する",
"1. BASE に油砥石をかける",
"2. 1.完成品にPIN PIN を圧入する"
],
"WorkPoints": [
"PIN の割り位置に注意して圧入する事",
"加工面全部に砥石をかける事",
"PIN PIN はﾃｰﾊﾟｰ側から圧入する事",
"ﾊﾞﾘ､ｶｴﾘ､打痕無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
|
{
"ToolName": "D-PIN圧入治具",
"Size": "",
"ToolOther": "FM-1169",
"WorkName": "BASE組立",
"WorkItems": [
"1. BASE に油砥石をかける",
"2. 1.完成品にPIN PIN を圧入する"
],
"WorkPoints": [
"加工面全部に砥石をかける事",
"PIN PIN はﾃｰﾊﾟｰ側から圧入する事",
"ﾊﾞﾘ､ｶｴﾘ､打痕無い事"
],
"Tolks": [],
"InspectionNo": "",
"InspectionItems": [],
"Words": []
}
|
{
"QualityItem": "取付確認",
"ToolManageNo": "FM-1169",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Other": "-",
"ProcessName": "-"
}
|
information_extraction
|
0
| null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.